View TLP10205_4131931.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TLP102
TOSHIBA PHOTOCOUPLER GaAAs IRED & PHOTO-IC
TLP102
Intelligent Power Module Signal Isolation Industrial Inverters Motor Drive
The Toshiba TLP102 consists of a GaAAs light-emitting diode and an integrated high-gain, high-speed photodetector. The TLP102 is suitable for isolating input control signals to intelligent power modules. This unit is a 6-pin MFSOP. The detector has a totem pole output stage to provide source drive and sink drive and features a built-in Schmitt trigger. The detector IC has an internal shield that provides a guaranteed common-mode transient immunity of 10 kV/s. The TLP102 is of an inverter logic type. A buffer logic version, the TLP106, is also available. Inverter logic type (totem pole output) Guaranteed performance over temperature: -40~85C Power supply voltage: -0.5~20 V Input current: IFHL = 3 mA (Max.) Switching time (tpLH/tpHL): 400 ns (Max.) Common-mode transient immunity: 10 kV/s Isolation voltage: 3750 Vrms TOSHIBA Weight: 0.09 g(typ.) 11-4C2 Unit in mm
Truth Table
Input H L LED ON OFF Tr1 OFF ON Tr2 ON OFF Output L H
Pin Configuration (Top View) 1
VCC
6
1:ANODE 3:CATHODE
3
SHIELD
GND
5:VO 4 6:VCC
5 4:GND
Schematic IF Tr1
ICC
6
IO Tr2
VCC
1
VF
3
5
VO
SHIELD
0.1 F bypass capacitor must be connected between pins 6 and 4
4
GND
1
2005-04-22
TLP102
Recommended Operating Conditions
CHARACTERISTIC Input Current, ON Input Voltage, OFF Supply Voltage Operating Temperature SYMBOL IF (ON) VF (OFF) VCC Topr MIN. 5 0 4.5 -40 TYP. MAX. 10 0.8 20 85 UNIT mA V V C
Maximum Ratings (Ta = 25C)
CHARACTERISTIC Forward Current LED Peak Transient Forward Current (Note 1) Reverse Voltage Output Current 1 (Ta 25C) DETECTOR Output Current 2 (Ta = 85C) Peak Output Current Output Voltage Supply Voltage Operating Temperature Range Storage Temperature Range Lead Solder Temperature (10 s) Isolation Voltage (AC,1 min., R.H. 60%, Ta = 25C) (Note 2) SYMBOL IF IFPT VR IO1 IO2 IOP VO VCC Topr Tstg Tsol BVs RATING 20 1 5 15/-15 4.5/-4.5 20/-20 -0.5~20 -0.5~20 -40~85 -55~125 260 3750 UNIT mA A V mA mA mA V V C C C Vrms
Note 1: Pulse width PW 10 s, 500 pps. Note 2: Product considered a two-terminal device: pins 1 and 3 shorted together and pins 4, 5 and 6 shorted together.
2
2005-04-22
TLP102
Electrical Characteristics (Unless otherwise specified, Ta = -40~85C, VCC = 4.5~20 V.)
CHARACTERISTIC Input Forward Voltage Temperature Coefficient of Forward Voltage Input Reverse Current Input Capacitance Logic LOW Output Voltage SYMBOL VF VF/Ta IR CT VOL TEST CIRCUIT 1 CONDITION IF = 5 mA , Ta = 25C IF = 5 mA VR = 5 V , Ta = 25C V = 0 , f = 1 MHz , Ta = 25C IOL = 3.5 mA , IF = 5 mA IOH = -3.5 mA, VF = 0.8 V VCC = 5 V VCC = 20 V VCC = 20 V Logic LOW Supply Current ICCL 3 IF = 5 mA Ta = -40~85C VCC = 5 V Ta = 25C VCC = 20 V Logic HIGH Supply Current ICCH 4 VF=0V Ta = -40~85C VCC = 5 V Ta = 25C Logic LOW Short Circuit Output Current Logic HIGH Short Circuit Output Current Input Current Logic LOW Output Input Voltage Logic HIGH Output Input Current Hysteresis IOSL 5 IF = 5 mA VCC = VO = 20 V VF = 0 V, VO = GND VCC = 20 V IO = 3.5 mA, VO < 0.4 V IO = -3.5 mA, VO > 2.4V VCC = 5 V MIN. 2.4 17.4 TYP. 1.5 -2.0 30 0.1 3.1 18.1 4.0 3.6 3.1 2.8 MAX. 1.7 10 0.35 6.0 mA 4.5 6.0 mA 4.5 UNIT V mV/C A pF V
Logic HIGH Output Voltage
VOH
2
V
7
37
mA
IOSH
6
-7
-40
mA
IFHL VFLH IHYS

0.8
0.3 0.05
3
mA V mA
*All typical values are at Ta = 25C.
Isolation Characteristics (Ta = 25C)
CHARACTERISTIC Capacitance Input to Output Isolation Resistance SYMBOL CS RS TEST CONDITION V = 0, f = 1 MHz R.H. 60%, VS = 500 V AC, 1 minute Isolation Voltage BVS AC, 1 second, in oil DC, 1 minute, in oil (Note 2) (Note 2) MIN. 1x10
12
TYP. 0.8 10
14
MAX.
UNIT pF Vrms Vdc
3750
10000 10000
3
2005-04-22
TLP102
Switching Characteristics (Unless otherwise specified, Ta = -40~85C,VCC = 4.5~20 V.)
CHARACTERISTIC Propagation Delay Time to Logic HIGH Output Propagation Delay Time to Logic LOW Output Switching Time Dispersion between ON and OFF Output Rise Time Output Fall Time Propagation Delay Time to Logic HIGH Output Propagation Delay Time to Logic LOW Output Common-Mode Transient Immunity at HIGH Level Output Common-Mode Transient Immunity at LOW Level Output *All typical values are at Ta = 25C. CML CMH 9 VCM = 1000 Vp-p, IF = 5 mA, VCC = 20 V, Ta = 25C -10000 SYMBOL tpLH tpHL |tpHLtpLH| tr tf tpLH 8 tpHL IF = 05 mA VCM = 1000 Vp-p, IF = 0 mA, VCC = 20 V, Ta = 25C 50 7 TEST CIRCUIT CONDITION IF = 50 mA, CL = 100 pF VCC = 20 V IF = 05 mA, CL = 100 pF VCC = 20 V CL = 100 pF IF = 50 mA, VCC = 20 V IF = 05 mA, VCC = 20 V IF = 50 mA MIN. 50 50 TYP. 250 270 MAX. 400 400 350 UNIT ns ns ns ns ns ns ns

50
175 95

400 400

10000
V/us
V/us
TEST CIRCUIT 1 : VOL
TEST CIRCUIT 2 : VOH
1 6 5 0.1uF VOL
V
IF
VCC 1
6 VCC 5
V
VOH
IOH VCC
3 SHIELD
GND 4
IOL
VCC 3 SHIELD GND 4
0.1uF
TEST CIRCUIT 3 : ICCL
IF 1
TEST CIRCUIT 4 : ICCH
6 5 ICCL
A
VCC
1
6 VCC 5
ICCH
A
VCC 3 SHIELD GND
VCC
3 SHIELD
GND
4
4
TEST CIRCUIT 5 : IOSL
TEST CIRCUIT 6 : IOSH
6 1 0.1uF
A
IF 1
VCC 5
6 VCC 5 0.1uF
A
VO VCC
3 SHIELD
IOSL GND 4 VO
VCC
3 SHIELD
IOSH GND 4
4
2005-04-22
TLP102
TEST CIRCUIT 7: Switching Time Test Circuit
IF
VCC 0.1uF
IF VO VCC
VOH tpHL tpLH
50%
SHIELD
GND
CL
90%
VO
1.3V
VOL tf tr
10%
TEST CIRCUIT 8: Switching Time Test Circuit
VCC IF VCC 0.1uF 620 tpHL VOH SHIELD GND CL 5k tpLH 90% VO 5V
IF
50%
VO
1.3V
VOL tf tr
10%
CL: stray capacitance of probe and wiring (to 15 pF)
TEST CIRCUIT 9: Common-Mode Transient Immunity Test Circuit
6 VCC 5 3 SHIELD VC 4 0.1uF VO VCC GND SW B : IF=0mA CMH 17V V SW A : IF=5mA CM L VCM 10% tr tf
SW A B
IF
90%
1000
VO
CM
H
=
800(V ) t r ( s)
CM
L
=
800(V ) t f ( s)
5
2005-04-22
TLP102
RESTRICTIONS ON PRODUCT USE
* The information contained herein is subject to change without notice.
20070701-EN
* TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer's own risk. * The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. * GaAs(Gallium Arsenide) is used in this product. The dust or vapor is harmful to the human body. Do not break, cut, crush or dissolve chemically. * Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations.
6
2005-04-22

▲Up To Search▲

Price & Availability of TLP10205

	To Download TLP10205 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .